Reply
 
Thread Tools Search this Thread Display Modes
 
Old 09-21-2018, 10:03 AM   #1
JustinChase
Junior Member
 
Join Date: Jul 2018
Posts: 26
Black and grey water tanks show full when they are not, how do I fix this?

So even when empty the black shows full and the grey shows 3/4 full, which is not ideal.


I understand 'stuff' can build up on the sensors and cause this, but how does one fix that?


Is there a better system I can install or upgrade to which will give me good, reliable readings that isn't susceptible to this sort of thing? I'd like to know I can always rely on the readings and not have to 'remember' when they might be full.
__________________

JustinChase is offline   Reply With Quote
Old 09-24-2018, 03:29 PM   #2
Mike_2015_3305
Junior Member
 
Join Date: Nov 2015
Posts: 2
after emptying the tanks fill them full of fresh water
then open the drain valve and let it flush out whatever
is in the tank. One tank at a time.

This usually works for me.
__________________

Mike_2015_3305 is offline   Reply With Quote
Old 09-25-2018, 05:44 AM   #3
Adam450
Junior Member
 
Join Date: Aug 2018
Posts: 1
Same here on levels

I have a cougar 2019 5th wheel with incorrect levels on my in-comand system.
One time my #1 gray tank showed 1/2 full. And it was full. I could hear bubbling in the shower drain.
Fresh water, filling it up and it was only showing 2/3 full. Water was coming out the fill nozzle.
Black tank. Your right, I don't take that chance and dump at 1/2 . With a good rinse.
I do not like running back to the dealer for this and every little problem. I feel it should be an easy fix for the owner.
I am thinking of filling my tanks with a measured amount of tank capacity water and see what it shows on the read out.
Any ideas?
Adam450 is offline   Reply With Quote
Old 09-25-2018, 09:52 AM   #4
Stripit
Senior Member
 
Join Date: May 2005
Location: Home Prescott, Az
Posts: 946
Send a message via AIM to Stripit Send a message via MSN to Stripit Send a message via Yahoo to Stripit
When my tank reading lights were showing wrong levels I would use the Flush King unit to back flush the tanks. I also would open up the basement side panels to expose the plumbing cleanout cap. Removed that cap and used my made up wand to put water pressure into that opening. I would force out the gray water holding tank "stuff" that was clinging to the sides of the tank. Tank readings worked again. About once every couple months or so I would do this where the park had terrific water pressure, made the job easier and faster.
__________________
2018 Holiday Rambler Admiral 31A
2015 Cadillac SRX (towed)
2008 Lexus 400H
1991 Avanti Conv
Stripit is offline   Reply With Quote
Old 09-25-2018, 01:08 PM   #5
BearKeller
Junior Member
 
Join Date: Aug 2018
Posts: 7
Most manufacturers use the problematic screw thur the sidewall of the tank system that always fail. I am picking up a new Jayco Pinnacle this week and one of me first mods will be to install a SEELEVELII monitor system made by Garnet Industries. Put one on my last RV and it was great and very accurate. Never had any problems. You do need to access the side of each tank and apply a special sensing tape on the outside of the tank. I then use a couple of the old sensor wires to connect to their panel. Not a easy install, especially if your not comfortable digging into the bowels of your unit.
BearKeller is offline   Reply With Quote
Old 09-25-2018, 09:14 PM   #6
wingnut60
Site Team
 
Join Date: Sep 2005
Location: Wherever the Suites is
Posts: 2,206
Another way to help clean the sensors is to drive between locations with about 1/3 full tanks with some sort of cleaning product added. In my previous Suites with the regular in-tank sensors, using bleach some times or Dawn some times or Cascade sometimes almost always resulted in good readings for some time, only to re-occur at a later time.
No longer a problem with the SeeLevel gauges in the '15 Suites.
__________________
2015 38RSSA #7382
2005 TK3 #1869, 10 yrs of memories
2017 F450 KR--one more Ford is it
2009 F450 4x4-died; 2010 F450-retired
wingnut60 is offline   Reply With Quote
Old 09-26-2018, 07:56 AM   #7
jmerritt
Junior Member
 
Join Date: Feb 2018
Location: Cincinnati, OH
Posts: 3
Put some dish soap a gallon of water and ice in empty tank just before you are ready to move. Towing will cause a scrubbing action of the ice and the dish soap will help break down the scum on the sides of the tank.
__________________

jmerritt is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 12:00 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2018, vBulletin Solutions, Inc.