|
10-19-2010, 09:05 PM
|
#1
|
Member
Join Date: Aug 2007
Posts: 89
|
Air Conditioner Filter Vents
Can anyone tell me how to make changing the Air Filters easier. By that I mean the screws in our 07 Elite has stripped out making the grille harder to install with the same screws. Must use larger and larger screws. Thanks to everyone who gave us a permanent fix on the basement door hinges. We fixed it from suggestions from this forum with no problems so far.
__________________
__________________
KEN
2007 Elite Suites 38 RL3 # 3633
2001 Chevy Dually 3500
|
|
|
10-19-2010, 09:55 PM
|
#2
|
Senior Member
Join Date: Jan 2008
Posts: 114
|
in each screw hole apply D.A.P wood putty allow to dry completly then replace the grill with your screws
__________________
|
|
|
10-20-2010, 08:21 AM
|
#3
|
Senior Member
Join Date: Jan 2006
Location: Currently: working on the road
Posts: 770
|
We use a hint that we found on forum years ago. Knobs are added on outside of vent with longer screws.
I still need a step ladder for the kitchen, but the bedroom vents are easy to access.
__________________
2014 Mobile Suite Estates 38RSB - custom home
2014 F450 KR CC 4x4 ...... his office
2015 Lance 1172 - traveling Motel (solar and generator)
Working Fulltimers since 3/2005
|
|
|
10-20-2010, 09:10 AM
|
#4
|
Senior Member
Join Date: May 2005
Posts: 2,130
|
After seeing that the factory only depended on the luan in the roof to hold the filter assembly in the ceiling I started looking for an alternative. I am familiar with a fastener made of sheet steel bent in a "U" shape for the purpose of mating with a screw. (I just can't think of the specific term for them right now, CRS, sigh) The "U" fits over the edge of the luan and has a large hole and a smaller hole designed to accept the threads of the screw. The smaller hole is placed on top so that as the screw tightens the entire clip then squeezes the whole thing together. The screws no longer use the luan for security and don't strip out.
__________________
Mike Nancy and the fuzzies
Fulltiming since June 2004
Volvo 660 MH tow vehicle
2005 MS 38RL
2007 Saturn Ion "toad"
2010 Gold Wing "piggyback"
|
|
|
10-20-2010, 09:40 AM
|
#5
|
Senior Member
Join Date: Jul 2005
Location: Liberty Mo (Suburb of Kcmo)
Posts: 559
|
AC vents
Mike,
I could be wrong probably am but I think they are called tinnermen. I suffer a lot from the same problem you have CRS
As always good camping
Joyce and Jerry
__________________
Jerry Sharp
Joyce McAlpin
Two Lives One Dream
2000 F 450 V10
5.38 gears trailer special
Automatic 4R100
20000# Reese Hitch
Trail Air Suspension and Pin Box with Tri Glide
Honda 4500 ex
Hughes Internet
Garmin 2720 talking GPS
Pressure Pro
Junk frame 2009 38TKSB3 #4750
|
|
|
10-20-2010, 10:03 AM
|
#6
|
Senior Member
Join Date: May 2005
Location: Home Prescott, Az
Posts: 1,019
|
I bought bolts with small washers and pushed them through from the top down and then used a washer & nut to tighten up to the ceiling panel. So all I had sticking down was the threads, and the nut just long enough for the grill to go into place and about 1/4 inch of threads still showing. Bought small knobs that then would screw onto the threads. Works perfectly and no more grills loosening up or screws that don't have anything to screw into.
__________________
2013 Tiffin Allegro 34 QFA
2015 Cadillac SRX (towed)
2019 Tesla Model X
1991 Avanti Conv
|
|
|
10-20-2010, 10:14 AM
|
#7
|
Senior Member
Join Date: May 2007
Location: Bouse, Az./Franklin,Pa.
Posts: 252
|
Quote:
I bought bolts with small washers and pushed them through from the top down and then used a washer & nut to tighten up to the ceiling panel. So all I had sticking down was the threads, and the nut just long enough for the grill to go into place and about 1/4 inch of threads still showing.
|
This is what I also did, but with white vinyl screws and nuts and white vinyl wingnuts to hold the grills and filters on.
__________________
Huck & Dodie
2005 RE3 MS #2163
2006 F-350 CC 4X4
|
|
|
10-21-2010, 08:35 AM
|
#8
|
Member
Join Date: Aug 2009
Location: way down here, FL
Posts: 70
|
You can also take oak strips of wood and glue to the luan, after glue dries predrill small holes in strips of oak wood. Now you can use original screws and the oak won't strip out if you do not overtighten them.
__________________
Jack
06 F-350 Lariat 4x4 V-10 CC SRW LB
06 Mobile Suites 36CK3
|
|
|
10-21-2010, 10:32 AM
|
#9
|
Senior Member
Join Date: May 2005
Posts: 2,130
|
Rotax,
Yup that was the name. I could recall the part just not the name. Easy fix though.
__________________
Mike Nancy and the fuzzies
Fulltiming since June 2004
Volvo 660 MH tow vehicle
2005 MS 38RL
2007 Saturn Ion "toad"
2010 Gold Wing "piggyback"
|
|
|
10-22-2010, 08:57 PM
|
#10
|
Member
Join Date: Aug 2007
Posts: 89
|
Where do I get these screws and wingnuts and does anyone recall the size?
__________________
KEN
2007 Elite Suites 38 RL3 # 3633
2001 Chevy Dually 3500
|
|
|
10-23-2010, 10:09 AM
|
#11
|
Senior Member
Join Date: May 2007
Location: Bouse, Az./Franklin,Pa.
Posts: 252
|
I picked them up at a hardware store. Maybe Home Depot or Lowes.
Probably got 10-24 3/4" nylon machine screws, nuts and wing nuts.
Just install the screws with nuts into the ceiling panel, then install the grill with the wingnuts.
__________________
Huck & Dodie
2005 RE3 MS #2163
2006 F-350 CC 4X4
|
|
|
10-23-2010, 10:20 AM
|
#12
|
Senior Member
Join Date: May 2007
Location: Bouse, Az./Franklin,Pa.
Posts: 252
|
I picked them up at a hardware store. Maybe Home Depot or Lowes.
Probably got 10-24 3/4" nylon machine screws, nuts and wing nuts.
Just install the screws with nuts into the ceiling panel, then install the grill with the wingnuts.
__________________
Huck & Dodie
2005 RE3 MS #2163
2006 F-350 CC 4X4
|
|
|
10-23-2010, 08:20 PM
|
#13
|
Junior Member
Join Date: Jan 2007
Posts: 19
|
I did what Jack described, except I used pine strips about an inch thick, and it has worked great.
Bob
__________________
Bob and Diana
2007 32TK3
Dodge 3500
|
|
|
11-10-2010, 09:00 PM
|
#14
|
Member
Join Date: Aug 2007
Posts: 89
|
Thank You All
Thanks to all of you who posted your ideas. Finally got back here to our resort to fix the A/C vent grilles. I used the 10/24/3/4 machine screws with wingnuts. Works great! Now Changing the filters will not seem like a daunting task. Took a little time to do, but will be well worth it the next time I change the filters. Again thank you all.
__________________
__________________
KEN
2007 Elite Suites 38 RL3 # 3633
2001 Chevy Dually 3500
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|