|
02-24-2009, 08:59 AM
|
#1
|
Senior Member
Join Date: May 2005
Posts: 2,130
|
Microwave oven light
For those who have not had this item go out yet I figured I'd post about the bulb in my unit. In this case it's the interior light rather than the exterior or bottom light.
I have the GE space maker microwave and convection oven model JVM1490BH. There are two lights in the unit, one for inside and the bottom counter light. Both bulbs are the same. They are available from Leows and I assume from other hardware stores as well. The Leows bulb is a Bright Effects #27217 20 watt halogen with 2 straight (bayonet) prongs. The bulb does not rotate to lock in place, it's just a friction fit. I got them for $4.98 each. I got two so I have a spare handy.
Before you do anything, unplug the oven!
The interior bulb is a minor pita to change out. You have to remove the wood trim above the oven held in place by 2 screws. Then you have to remove the vented top trim from the oven. It is also held by 2 screws in the top of the oven. You'll need a short philips screw driver for that. The screws are the forward most 2 screws in the unit. The trim will then pivot forward and out as the bottom is held by a couple of hooks.
Look to a small grayish plastic vent in front of the unit. This may have a small screw in front or be held in place on the right side by a small tab. Mine had a tab that you light the right side past. The vent is held in place by a screw on the back side. Just loosen it and pivot the vent out of the way to the left. You'll need a really short phillips screw driver for that and the rest of the job.
There is a small shiny cover held in place by a couple screws right behind that plastic vent. Remove the screws and the cover will slide to the right to come out. It covers the light assembly. Inside a small opening you will see a pair of white wires going inside of another cover. Those are the bulb power leads. That small cover is held in place by a tab on the right side and a hooked ridge on the left. You have to squeeze the light shield / reflector to the left to unlatch it them pivot the thing up and right to take it out. The bulb will be attached to it. the bulb is a tight (very damn tight) friction fit and may have a small dab of some kind of adhesive on it. At least mine did. Just pull it straight out.
Take the new bub, holding it in a piece of paper towel and insert it in place. DO NOT TOUCH THE NEW BULB WITH YOUR BARE HANDS OR ANYTHING DIRTY, IT WILL DRASTICALLY SHORTEN THE LIFE OF THE BULB.
Assemble the unit in reverse order. It takes about 5 to 10 minutes or so once you've done it before and it sounds harder than it is. It does help to have small hands when doing the job especially in getting the bulb holder in and out of the space it's in. Beware of sharp edges in the sheet metal in that area.
The bottom or counter light is simple. Remove the single screw holding the light lens. The lens will pivot down. Remove the bulb from the holder and replace.
Again they are both the same bulb. GE only has their part number on their site and tech center, so no help there for the bulb model.
__________________
Mike Nancy and the fuzzies
Fulltiming since June 2004
Volvo 660 MH tow vehicle
2005 MS 38RL
2007 Saturn Ion "toad"
2010 Gold Wing "piggyback"
|
|
|
02-24-2009, 09:05 AM
|
#2
|
Senior Member
Join Date: Nov 2005
Location: Springfield, Il.
Posts: 655
|
Nice post Mike.
I'm sure it will help someone who hasn't had the privilege of changing one out yet. lol
__________________
Ponch
S.O.I.T.C. Central Division
2007.5 3500 HD GMC dually
Mobile Suites 2005 36CK3 #2307 w/ auto levelers/ phase 2
Air Safe Hitch
HD TV in the basement and living room and bedroom
HD MOTO SAT Auto Ant on roof
pressure pro
|
|
|
02-24-2009, 09:55 AM
|
#3
|
Senior Member
Join Date: May 2007
Location: Bouse, Az./Franklin,Pa.
Posts: 252
|
http://cgi.ebay.com/5pcs-G8-44mm-JCD...3A1%7C294%3A50
Here is a great deal on those bulbs with free shipping. I went for it with no problems at all.....
__________________
Huck & Dodie
2005 RE3 MS #2163
2006 F-350 CC 4X4
|
|
|
02-24-2009, 10:49 AM
|
#4
|
Senior Member
Join Date: Oct 2006
Location: New Lisbon, Wisconsin
Posts: 317
|
Thanks for the info, is this the same way to get at the top filter so that it can be changed and where can a new replacement be purchased?
__________________
06 MS 36TK3 #2473 w/(Phase II)side to side levelers, Trailair pin box w/Tri-Glide plate.
2011 Dodge 3500 CC 4x4 Diesel DRW Power Tuner guages etc
|
|
|
02-25-2009, 09:20 AM
|
#5
|
Senior Member
Join Date: May 2005
Posts: 2,130
|
That is the route to the filter but my model vents to the outside so I don't have any idea about replacements. You can probably find them on the GE website or call around to the appliance stores. If you take it out you might be able to match it at a hardware store too.
__________________
Mike Nancy and the fuzzies
Fulltiming since June 2004
Volvo 660 MH tow vehicle
2005 MS 38RL
2007 Saturn Ion "toad"
2010 Gold Wing "piggyback"
|
|
|
02-25-2009, 09:42 AM
|
#6
|
Senior Member
Join Date: Jan 2006
Posts: 105
|
My inside light bulb went out after a couple months and I had GE send their tech out to replace it because I had no idea where in the heck it was.
I watched the tech with a eagle eye so I could do it next time when it's out of warranty.
Bob
|
|
|
02-25-2009, 09:47 AM
|
#7
|
Senior Member
Join Date: Mar 2006
Location: Austin Arkansas
Posts: 399
|
And, you can get the replacement bulbs at WalMart. I had this issue in the past and when it burnt out again, I picked up two at WalMart .
__________________
John & Peggy
1SG US Army Retired
|
|
|
02-25-2009, 12:07 PM
|
#8
|
Senior Member
Join Date: Oct 2006
Location: New Lisbon, Wisconsin
Posts: 317
|
Motor31- Mine also vents to the outside, but I think their is another filter on the top, behind the lovered cover.
__________________
06 MS 36TK3 #2473 w/(Phase II)side to side levelers, Trailair pin box w/Tri-Glide plate.
2011 Dodge 3500 CC 4x4 Diesel DRW Power Tuner guages etc
|
|
|
02-26-2009, 09:02 AM
|
#9
|
Senior Member
Join Date: May 2005
Posts: 2,130
|
Ron,
I looked around inside there when I had it apart and didn't see any filter. I did look over the installation guide for the unit. It had a portion of the guide dedicated to using a non vented installation. In that case they moved the main fan position to blow forward and installed the optional filter on top by the grill. That may be what you are thinking about.
__________________
Mike Nancy and the fuzzies
Fulltiming since June 2004
Volvo 660 MH tow vehicle
2005 MS 38RL
2007 Saturn Ion "toad"
2010 Gold Wing "piggyback"
|
|
|
06-25-2014, 05:50 PM
|
#10
|
Junior Member
Join Date: Jun 2014
Location: Lake of the Ozarks, MO
Posts: 1
|
GE Microwave/Convection Spacemaker - Oven light replacement
Hey, Mike -
Just wanted to thank you for posting instructions on replacing the interior halogen light bulb in our GE Spacemaker Micro/Convect oven. We bought our 5th wheel over a year ago & the light had not worked from day 1. I found your advice after Google-ing the GE model number & "bulb replacement". I read the instructions to Jerry while he did the work. It took us about 20 minutes, but we got it done! We found the light bulb at Lowe's. They no longer carry the brand you'd mentioned, but were able to find us the right one: FEIT Electric G8.6 Halogen
Now I can finally see what I'm cooking.
:)
__________________
Jerry, Deborah & Weezer
2006 DRV 36TK3
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|